
How to Assemble a Neon Sign: A Practical Guide
A step-by-step guide to unboxing, mounting, wiring and testing a custom LED neon sign — plus the mistakes that cause flicker and how to avoid them.
Neon signs are one of the fastest ways to make a shopfront, studio or reception wall feel deliberate. Modern signs sold in Kenya are not glass gas tubes — they are flexible LED ribbon set into a shaped acrylic backer, supplied with a 12 V transformer. That changes the assembly job: there is no glass to bend or gas to handle, but the mounting and wiring still need care.
This guide covers the assembly sequence we use in our Nairobi workshop, and the checks that stop a sign flickering or failing after a few weeks. If you would rather have us handle it, every LED neon sign we sell can be delivered pre-wired and installed by our team.
What should be in the box
A complete kit should contain the neon panel itself, a 12 V transformer (often with a UK or EU plug), mounting screws or standoffs, a template or drilling guide, and a short wiring diagram. If any of those are missing, stop before you drill — a replacement transformer is cheap, but a sign mounted in the wrong place is not.
- Panel: acrylic backer with the LED ribbon and a clear or coloured face.
- Transformer: 12 V DC, rated above the sign's total wattage.
- Fixings: standoffs for a floating look, or screws and wall plugs for a flush mount.
- Template: full-size paper guide showing the fixing points.
1. Inspect before you install
Plug the sign in on a protected surface before mounting it. Check that every segment lights, that the colour is even, and that the transformer does not buzz loudly. LED neon is low-voltage, but the transformer still needs to sit in a dry, ventilated spot — not inside a sealed cabinet and not on a wet floor.
Photograph the sign and the serial number on the transformer. If a segment fails inside the warranty window, that photo makes the claim straightforward.
2. Choose the mounting height
For a wall-mounted sign viewed from two to three metres away, the centre of the sign usually sits at 1.5–1.7 m. Above a reception desk, aim for the sign's centre to land roughly at eye level for someone standing at the counter. For a shopfront, check the sightline from the pavement: a sign that looks right from inside is often too high or too low from outside.
Use the paper template to mark the fixing points, then check the marks with a spirit level before drilling. Acrylic is unforgiving of a hole in the wrong place.
3. Mount the backer first
Fix the standoffs or screws into the wall, leaving enough protrusion for the acrylic thickness. For drywall, use anchors rated for at least twice the sign's weight; for concrete or block, use SDS anchors. If the wall is glass, switch to standoff barrels with VHB tape and mechanical fasteners rather than drilling the glass.
Lift the sign onto the fixings with two people. A 60 × 40 cm panel is light, but it is awkward, and a cracked corner is a full replacement.
4. Connect the transformer
Run the low-voltage cable from the sign to the transformer, then the transformer to the nearest socket. Keep the low-voltage cable clear of sharp edges and avoid daisy-chaining multiple signs onto one undersized transformer. If the sign is outdoors, the transformer must be inside an IP-rated enclosure and the cable glands sealed.
Turn the transformer on only after every connection is made. A brief flash when you plug in is normal on some drivers; a persistent flicker is not.
Troubleshooting a sign that will not light
| Symptom | Most likely cause | What to check |
|---|---|---|
| Nothing lights | No power at the socket or a loose DC plug | Test the socket with another device, then reseat the DC connector. |
| One segment flickers | A partial ribbon failure or a loose splice | Check the splice at the end of that segment; a failed segment is a warranty job. |
| Sign dims when another appliance starts | Transformer too small or a shared circuit | Move the sign to its own circuit or upgrade the transformer. |
| Transformer buzzes loudly | Cheap driver or loose mounting | Mount the driver on rubber washers; replace if the buzz persists. |
Maintenance that actually matters
Dust the acrylic face with a soft dry cloth. Avoid solvent cleaners, and do not pressure-wash an outdoor sign. Once a year, check that the cable gland is still sealed and that the transformer enclosure has not filled with condensation. That is the whole maintenance routine — LED neon has no tubes to replace.
When to let a professional install
If the sign is above a walkway, on a glass facade, or part of a multi-branch rollout, use an installer. The risk is not the wiring; it is the fixing, the cable route and the permit. Our team installs across Nairobi and delivers countrywide — start with the neon sign product page for sizes and pricing, or compare it with a backlit lightbox if you need a larger illuminated face.
If you are still deciding between neon and a fabricated sign, read our backlit and neon signs category first, then send us the wall dimensions through the contact page and we will quote both options.


